Motion

The FTC Starter Kit V3.1 is the ultimate starting point for your team’s FIRST Tech Challenge season. Built based on feedback directly from teams, this kit is packed with essential REV DUO components you need to design, prototype, and compete...

The REV UltraPlanetary Gearbox Kit is the entry point into using the REV UltraPlanetary System. The kit comes with UltraPlanetary Cartridges to support six different final gear reductions ranging from nominally 3:1 to 60:1 allowing for the right amount...

This bearing pillow block bracket (REV-41-1317) is used with the DUO Build System 15mm Extrusion. The 9mm center hole is use with either the Long Through-bore Bearing (REV-41-1329) or the End Cap Bearing (REV-41-1322) to provide a low friction shaft...

M3 Spacers are compatible with the REV DUO System and accurate way to space gears, sprockets, wheels, and other parts on a M3 bolt.  

5mm Hex Spacers are compatible with the REV DUO System and accurate way to space gears, sprockets, wheels, and other parts along a 5mm hex shaft. Mix and match various spacer lengths to adjust spacing in increments as small as 1.5mm...

M3 Ball Joint Rod Ends are compatible with the REV DUO System. The Female M3 Ball Joint Rod End (REV-49-1560) can either be paired with its male counterpart to create short linkage arms or with M3 threaded rod and a second female ball...

5mm Metal Hex Bore Gears are compatible with the REV DUO System and work with REV 5mm hex shafts in high-load applications. REV metal gears are NOT compatible with REV plastic gears. All REV metal gears are narrower than plastic...

5mm Plastic Hex Bore Gears are compatible with the REV DUO System and fit on a 5mm hex shaft. The hex shaft interface completely eliminates the need for expensive hubs or using potentially unreliable set screws. Gears 45 tooth...

DUO Plastic #25 Sprockets are compatible with the REV DUO System and fit on a 5mm hex shaft. The hex shaft interface completely eliminates the need for expensive hubs or using potentially unreliable set screws. Sprockets 15 tooth and...

This Motion Pattern Spacer offers a convenient and accurate way to space gears, sprockets, wheels, and other parts through the Motion Pattern interface. Great for getting the proper spacing when face mounting to the UltraPlanetary Gearbox...

This is all of the hardware included in the 15mm Linear Motion Kit V2 (REV-45-1507). Specifications Hole Diameter: M3 Clearance Kit Contents QTY 8 - M3 x 8mm Low Profile Socket Screws QTY 8 - M3 x 8mm Hex Cap Screws QTY 8 - M3 Nyloc Nuts QTY 8 - M3...

Make driving linear motion easy with the 22 Tooth Plastic Right Angle Rack Gear. Mount the rack gear to a slot in either the REV DUO Extrusion or REV DUO Channel while using any of the REV DUO Plastic Gears to drive motion. Specifications Module: 0...

Our Polyurethane Hollow Round Belting is perfect for your conveyor, and intake mechanisms. Use Barbs to assemble custom length belts. 

This shaft collar is compatible with the DUO Build System and is used to prevent gears, sprockets, wheels, and other parts from sliding out of place on a 5mm hex shaft. Shaft collars can also be used to prevent the shaft itself from sliding out of its...

The Servo Shaft Adapter makes it possible to drive a 5mm hex shaft with any 25T output servo including the Smart Robot Servo. The adapter attaches to the servo spline like any common servo horn and accepts a 5mm hex shaft on the opposite end...

1.2mm UHMWPE Cord - 10M (REV-41-1162) is a high strength string for use with the small Pulley Bearings and the 15mm Linear Motion Kit to create a powered lift.   3mm UHMWPE Cord - 10m (REV-29-1244) is a high-strength and low-stretch...

Complete gear set replacement for the Smart Robot Servo V2. Documentation Smart Robot Servo V2 Overview Smart Robot Servo V2 - Balanced Gear Replacement Guide

This Servo Gear Adapter is a 15 Tooth Plastic Gear that attaches to any 25T output servo including the Smart Robot Servo. Warning: Gears from other building systems may have a very similar tooth profile but are not an exact match. It may be possible to...

Metal sprockets designed to work in high-load applications with #25 chain. This sprocket requires a hub like REV-41-1719. Specifications Chain Size: #25 Material: 6061 Aluminum Documentation SprocketGuide BuildingGuide Product...

DUO Traction Wheels are compatible with the REV DUO System and fit on a 5mm hex shaft. The hex shaft interface completely eliminates the need for expensive hubs or using potentially unreliable set screws. DUO Traction Wheels 60mm in...