FIRST Robotics Competition

This Eye-to-Eye Turnbuckle is ideal for tensioning string, cordage, or cabling in linear motion applications. The welded eyes provide significantly more strength than bent eyes. Specifications Material: Steel Thread: M5 Retracted Length: 106mm +-...

Split Lock washer with a 3/8in inner diameter. Specifications Material: Zinc-plated Steel ID: 3/8in OD: 0.680in Thickness: 0.094in Documentation ION Build System Guide #10 Hardware Basics CAD & Drawings REV-29-1240 Drawing

Steel hardware of the appropriate size to work with the ION Build System 1in Extrusion. Length measured from tip to underside of screw head. Specifications Material: 18-8 Stainless Steel Diameter & Thread: #10-32 Length: 1-1/2in Documentation ION...

Steel hardware of the appropriate size to work with the ION Build System 1in Extrusion. Length includes the flat screw head. Specifications Material: 18-8 Stainless Steel Diameter & Thread: #10-32 Length: 1/2in Documentation ION Build System...

The 1in Inside Corner Bracket is designed to enable more construction strategies with the 1in Extrusion. Designed for #10 hardware, the mounting holes are on a 1in pitch that allows for the creation of complex joints by stacking with other 1in...

The 1in Extrusion Endcap Slide allows teams to create compact and robust multistage lifts when combined with the 1in Linear Motion Kit (REV-15-1189) and the 1in Extrusion (REV-21-1000). The slide tab is offset allowing stages to fully nest when collapsed...

The REV POE Injector Cable was specifically designed to address a common problem for many FRC teams with their wireless radios: intermittent power glitches. The wireless radios used in the last several FRC seasons can be powered either through a...

This 12V RGB LED Strip is compatible with the REV Blinkin LED Driver (REV-11-1105). Each LED on the strip is wired in parallel and actually contains three embedded LEDs; a red, green, and blue LED. Each color can be controlled separately to create any...

For use with the ION Build System 1in Extrusion to create linear motion.   Kit Contents QTY 1 - REV-21-1032 - Dual Bearing Plate QTY 1 - REV-21-1029 - Eccentric Bushing QTY 1 - REV-21-1030 - Concentric Bushing QTY 2 -...

Extend the reach of your MXP port by using this 18" cable to reposition your boards where you need them. Fully compatible with all REV Robotics MXP accessory boards (More Board, Proto Board, & RIOduino) Specifications Keyed male and female...

The REV Robotics Digit is multi-use MXP board for interface with the roboRIO. It has four 12 segment displays, which can be used to show any letters or numbers. It also features an analog potentiometer and two momentary buttons. Teams can use the...

Eccentric bushings are used to hold our V-Groove Bearings (REV-29-1014) for linear motion applications. The hole is drilled off-center of the bearing axis so by rotating the bushing on its mounting bolt, the clearance between the wheel and track can...

This dual bearing plate holds two V-Groove Bearings (REV-29-1014) to create an easy linear motion system for the ION Build System 1in Extrusion (REV-21-1000). Using a combination of Concentric (REV-21-1030) and Eccentric (REV-21-1029) bushings, the user...

Concentric bushings are used to hold our V-Groove Bearings (REV-29-1014) for linear motion applications. Used in conjunction with our Eccentric Bushing (REV-21-1029), the user can adjust how tight or loose they would like to tune their linear...

REV Polycarbonate Sheets are lightweight, clear, and impact-resistant plastic sheets for robot construction, prototyping, covers, guards, sponsor panels, intake surfaces, funnels, and other custom mechanisms. Polycarbonate is durable while still allowing...

The JST PH 6-pin Joiner Boards (REV-11-1277-PK4)  are intended to be used with the JST PH 6-pin Extension Cables to extend the reach of your NEO Brushless Motor sensor cables. The JST VH 2-pin Joiner Board - 4 Pack (REV-31-1429-PK4) are small...

The SPARK Flex Data Port Breakout Cable (REV-11-2853) breaks out the default pin functions of the SPARK Flex Data Port into commonly used connectors for external sensors. The keyed and locking Data Port connector ensures a secure and aligned fit when...

The USB-A to USB-C 2.0 Cable - 2m (REV-11-1232) is a longer version of the USB-A to USB-C cable included with the SPARK MAX Motor Controller and the Control Hub. Use this cable to connect your SPARK MAX or Control Hub to a standard computer from up to 2...

1.2mm UHMWPE Cord - 10M (REV-41-1162) is a high strength string for use with the small Pulley Bearings and the 15mm Linear Motion Kit to create a powered lift.   3mm UHMWPE Cord - 10m (REV-29-1244) is a high-strength and low-stretch...

Absolute Encoder Adapter (REV-11-3326) connects the REV Through Bore Encoder directly to the SPARK MAX Data Port. This adapter connects the Absolute Duty Cycle output of the Through Bore Encoder to the correct SPARK MAX Data Port pins while leaving the...