FIRST Tech Challenge

The FTC Starter Kit V3.1 is the ultimate starting point for your team’s FIRST Tech Challenge season. Built based on feedback directly from teams, this kit is packed with essential REV DUO components you need to design, prototype, and compete...

The EDU Kit V2 was specifically created to implement hands-on STEM projects in the classroom. This upgrade bundle bridges the gap between the EDU Kit V2 (REV-45-2041) and the FTC Starter Kit V3.1 (REV-45-3529), providing the needed equipment to...

The REV USB PS4 Compatible Gamepad is compatible with both the REV DUO and REV ION Systems. Plug the REV Gamepad directly into a Driver Hub to enable feature rich control of your robot. Additionally, when plugged into a PC, it offers an Xbox...

The REV UltraPlanetary Gearbox Kit is the entry point into using the REV UltraPlanetary System. The kit comes with UltraPlanetary Cartridges to support six different final gear reductions ranging from nominally 3:1 to 60:1 allowing for the right amount...

REV 45mm U Channel has a 45mm x 45mm square profile, and is designed to work seamlessly with existing REV 15mm Extrusion. It can be used in locations where additional torsion strength is required. On the sides of the channel is the Extended Motion...

The UltraUSB Hub is designed specifically for use in competitive robotics, and gives you the ability to connect multiple USB devices to each other as well as replacing cables when damaged instead of needing to replace the whole hub. The UltraUSB Hub can...

This bearing pillow block bracket (REV-41-1317) is used with the DUO Build System 15mm Extrusion. The 9mm center hole is use with either the Long Through-bore Bearing (REV-41-1329) or the End Cap Bearing (REV-41-1322) to provide a low friction shaft...

Hex keys, also known as Allen wrenches or L-keys, are essential hand tools designed to drive screws and bolts with hexagonal recesses. They are widely used in robotics, engineering, and general assembly for tightening or loosening fasteners in compact or...

M3 Spacers are compatible with the REV DUO System and accurate way to space gears, sprockets, wheels, and other parts on a M3 bolt.  

Washer for use with REV DUO M3 hardware.

5mm Hex Spacers are compatible with the REV DUO System and accurate way to space gears, sprockets, wheels, and other parts along a 5mm hex shaft. Mix and match various spacer lengths to adjust spacing in increments as small as 1.5mm...

M3 Ball Joint Rod Ends are compatible with the REV DUO System. The Female M3 Ball Joint Rod End (REV-49-1560) can either be paired with its male counterpart to create short linkage arms or with M3 threaded rod and a second female ball...

5mm Metal Hex Bore Gears are compatible with the REV DUO System and work with REV 5mm hex shafts in high-load applications. REV metal gears are NOT compatible with REV plastic gears. All REV metal gears are narrower than plastic...

5mm Plastic Hex Bore Gears are compatible with the REV DUO System and fit on a 5mm hex shaft. The hex shaft interface completely eliminates the need for expensive hubs or using potentially unreliable set screws. Gears 45 tooth...

DUO Plastic #25 Sprockets are compatible with the REV DUO System and fit on a 5mm hex shaft. The hex shaft interface completely eliminates the need for expensive hubs or using potentially unreliable set screws. Sprockets 15 tooth and...

15mm Plastic Motion Brackets are compatible with the REV DUO System. Each bracket features a set of alignment ribs designed to seat the bracket into the extrusion channel increasing joint alignment, strength, and rigidity.  The 15mm Plastic...

DUO L Beams are compatible with the REV DUO System and are a structural element for small load applications or as a supporting component on a larger load application. They are compact, lightweight, and provide more strength than a flat beam. Use them to...

DUO Flat Beams are compatible with the REV DUO System and are easy to use. Having an 8mm width, 3mm height, and 8mm hole pattern makes them perfect as a support for an upright or using them as a linkage.  Specifications Material: 6063...

The USB Female A to Micro USB Adapter allows you to use standard USB devices with micro 5-pin oriented electronics. Use this cable adapter to connect a Robot Controller phone to an Expansion Hub, or to connect a Driver's Station phone to a single...

The 5.5mm WERA Socket Screw Driver is for use with M3 hex head screws and nuts. Kraftform Ergonomic Micro handle design features the shape that facilitates high torque transfer and precision feel for fine adjustment work,...