Electronics

2-pin header cable that can be used for connecting signals, sensors or any other spots on robots. Features 2 female 0.1in pitch connectors on each end.  Specifications Length: 91cm (36in) 2 pin receptacle on 0.1in pitch Wire Colors: red, black 22...

The Molex MicroFit+ Power and CAN Cable is the dedicated replacement and accessory cable for the MAXSpline Through Bore Encoder. It provides both power and CAN connectivity through a compact, secure 2x2 Molex MicroFit+ latching connector. While currently...

The Digital LED Indicator is a LED signal module that is digitally controlled (active low) and offers three colors: red, green, and amber. The Digital LED Indicator is designed to directly interface with the DIO ports of the Expansion Hub or Control Hub...

Touch sensor is best used for user input, but can also be used as a limit switch.  Configuration The REV Touch Sensor is a digital sensor that is wired to the N+1 channel on our standard 4-pin JST PH connector. In other words, the REV Expansion Hub...

The 36in CAN Extension Cable is a 3-pin connector to interface with existing CAN devices.  Specifications Length: 36in (3ft) Wire Colors: yellow, green 22 AWG

This JST-PH 6-pin Breakout Board is designed to adapt external sensors to the SPARK MAX 6-pin Encoder Port standard. It features a JST PH 6-pin connector, labeled solder pads, and through-hole pads that are compatible with popular 63R style quadrature...

These plastic clips are designed to keep standard 0.1" 3-pin PWM connectors together. Simply clip them around an assembled pair of connectors.

The NEO 2.0 Sensor Cable connects the NEO 2.0 Brushless Motor’s sensor port to a standard JST PH 6-pin interface used on REV motor controllers. The 2x3-pin PHSD connector provides a secure, latching connection at the motor, while the 6-pin JST PH...

The CAN Terminator Pack provides two compact, plug-ready termination options for teams looking to maintain reliable CAN bus performance anywhere in their robot’s wiring. Each terminator uses a small 10mm x 10mm internal circuit board sealed with...

The MAXSpline Grommet provides a simple way to route wires through MAXTube while preventing abrasion against bare aluminum. Made from pliable 60A rubber, it press-fits into the MAXSpline Bore on MAXTube with a 1/8 inch wall, creating a clean pass-through...

The REV Through Bore Encoder V2 provides precise, reliable shaft position measurement with both incremental (ABI quadrature) and absolute (pulse-width) outputs. Its ½" hex through bore mounts easily within common FRC/FTC mechanisms, and the...

The SPARK MAX Data Port Breakout Board makes it easy to connect external sensors to the SPARK MAX Data Port. For additional information on the SPARK MAX Data Port, please take a look at the SPARK MAX User's Manual. Analog Input Issue - Affects Rev. A...

REV Robotics custom ATO sized auto-resetting breakers are designed to give reliable protection for FRC robot actuators.  These custom developed breakers adhere to SAE Standard J553 and will give consistent performance even after hundreds of breaker...

The REV Servo Hub is compatible with both the REV ION and REV DUO systems. Over a single communication interface it can provide advanced control of up to six (6) servos. This means that the Servo Hub needs no additional PWM cabling between it and your...

Mounting your SPARK MAX Motor Controller (REV-11-2158) has never been easier with the help of the SPARK MAX Mounting Bracket. Configured with a hole pattern compatible with a 1/2in grid and allowing the mode and status light to be seen, this...

This update to the SPARK CAN Cable bridges the H and L CAN signals together within the cable itself. This prevents the CAN Bus breaking in the event of a cable disconnecting from a SPARK MAX Motor Controller. These SPARK CAN cables have a JST-PH 4-pin...

The REV Robotics 2m Distance Sensor uses the ST Microelectronics VL53L0X Time-of-Flight (ToF) laser-ranging module to measure distances up to 2 meters with millimeter resolution. Unlike other ranging sensors that rely on the intensity of reflected light,...

The REV Robotics Magnetic Limit Switch is a three-sided active-low digital hall effect switch with three internal hall effect elements located on the top and sides of the sensor. The three elements are connected in parallel so that any one of them will...

These JST PH 6-pin Extension Cables are intended to extend the reach of sensor cables without having to cut and splice wires. Specifications REV-11-1275-PK4: Length: 90cm (35.5in) REV-11-3327: Length: 30cm (11.81in)

The REV Robotics Analog Pressure Sensor is a 5V sensor that can measure pressures up to 200 PSI. It outputs an analog voltage that is proportional to the measured pressure and can plug directly into the roboRIO or the More Board V2.0...