Competition

With an efficient right-angle configuration, the Ultra 90 Degree Gearbox offers a robust solution to building a more compact robot. The Ultra 90 Degree Gearbox allows you to connect the UltraPlanetary Gearbox and the HD Hex Motor (REV-41-1600)...

An individual cartridge for the UltraPlanetary System. This cartridge is nominally a 5:1 gear reduction. The UltraPlanetary System is a cartridge based modular gearbox designed to handle the rigors of the competition and the classroom. Building on...

An individual cartridge for the UltraPlanetary System. This cartridge is nominally a 4:1 gear reduction. The UltraPlanetary System is a cartridge based modular gearbox designed to handle the rigors of the competition and the classroom. Building on the...

An individual cartridge for the UltraPlanetary System. This cartridge is nominally a 3:1 gear reduction. The UltraPlanetary System is a cartridge based modular gearbox designed to handle the rigors of the competition and the classroom. Building on the...

This sensor can be used to read and compare colors, and also has a built-in IR (optical) Proximity Sensor and white LED for active target lighting. Supports High Speed I2C Communication (400kHz) as well as auto increment register read which allows the...

The REV Robotics 2m Distance Sensor uses the ST Microelectronics VL53L0X Time-of-Flight (ToF) laser-ranging module to measure distances up to 2 meters with millimeter resolution. Unlike other ranging sensors that rely on the intensity of reflected light,...

The REV Robotics Magnetic Limit Switch is a three-sided active-low digital hall effect switch with three internal hall effect elements located on the top and sides of the sensor. The three elements are connected in parallel so that any one of them will...

Easily connect multiple devices to your robot battery with the XT30 Power Distribution Block. Allows for clean, compact wiring of all your XT30-connected devices. Compatible with: Expansion Hub, Blinkin LED Driver, SPARKmini, Servo Power Module, and many...

These JST PH 6-pin Extension Cables are intended to extend the reach of sensor cables without having to cut and splice wires. Specifications Length: 30cm Notes As of 01/10/2024, the length on this product page has been corrected from 15cm to 30cm...

The 1in Pivot Joint is compatible with the REV ION System. Create a pivot joint at the end of a piece of MAXTube - 1x1 with Grid Structure. Specifications Material: POM (Acetal/Delrin) Documentation REV ION Build System Documentation Introduction...

The REV Robotics Analog Pressure Sensor is a 5V sensor that can measure pressures up to 200 PSI. It outputs an analog voltage that is proportional to the measured pressure and can plug directly into the roboRIO or the More Board V2.0...

The REV Driver Hub is a compact mobile computing device designed for interfacing with the Control Hub (REV-31-1595). The Driver Hub was designed and built as an easy to use, dependable, and durable device for use in classroom and the competition. It...

With over 180 parts, the EDU Kit V2 is specifically created to implement hands-on STEM projects in the classroom. This robotics kit is used to teach a variety of lessons ranging from computer programming and engineering principles to project management...

The FTC Timing Belt and Pulley Bundle contains an assortment of components needed for a pulley-based motion transmission system. Timing Belts and Pulleys are lighter, more compact, and more efficient at transferring motion than chain and sprockets...

The 5mm Hex Shaft and Spacer Bundle features an assortment of REV products that work to transmit intended motion and constrain unintended motion in the DUO Build System. Use this bundle to restock your existing shaft and spacer supply, or as a great...

The FTC Cable Bundle offers a plethora of major cables and other accessories for a variety of robot design needs, without having to sacrifice wiring best practices. Necessary cables, like the XT30 Extension Cable, come in two different...

The C Channel Bundle contains various lengths of 45mm x 15mm C Channel and is designed to work seamlessly with existing REV 15mm Extrusion. They can be used in locations where additional torsional strength is required. The 45mm wide side...

The U Channel Bundle contains multiple lengths of 45mm U Channel and is designed to work seamlessly with existing REV 15mm Extrusion. The U Channel Endcap and Tensioning Bushing allows users to fine tune their system when designing and...

The 15mm Extrusion Lift Kit offers an assortment of components needed to build an un-powered 3-stage continuous or cascading lift. The basics of the linear motion kit can be found on the Introduction to Linear...

The FTC Sensor Bundle offers an assortment of REV Sensors and sensor accessories to help your robot understand the world around it. Use this bundle to restock your existing sensor supply, or as a great starting point for a new FTC team...